Close

Less prototyping rounds and EMC challenges with simulation

Published: 29.12.2017 - 17:00:00
Back to References

Simulation speeds up design and helps improve the end product quality. EMC, or Electromagnetic Compatibility, is wise to be taken into account in design from the very beginning.

”In far too many projects the EMC requirements are remembered only at the very end of the development project. In the worst case, the design has to be completely restarted if the product causes radio frequency emissions more than the regulations allow, or the product does not function properly due to radio frequency interference”, warns Senior EMC Specialist Marko Luukkainen. Luukkainen, who works in Etteplan’s Jyväskylä unit, has got over 20 years of experience in RF and EMC field.

Example2.jpg

Picture - RF Immunity Simulation. The device (model) is placed in a virtual test chamber and the device is exposed to RF radiation of different frequencies from various angles. Red color represents possible high vulnerability.

What if the EMC problem is nevertheless detected in the measurements only when the deadline is already approaching?

”There are many ways to act. Luckily, simulation helps recognize the problems and develop fixes as fast as possible. But when the fixes need to be done in a hurry, the functional quality and features of the product may have to be compromised. Also, the manufacturing costs may increase. The best results are achieved, when EMC is taken into account from the very beginning of the project”, reminds Luukkainen.

”EMC reviews and simulations are worth including to the development project from the beginning of electronics and mechanical design”, emphasizes Marko Luukkainen.

 

Old working methods revised

 

The traditional product development way of working is familiar to us all. Design, manufacture prototypes, measure, make the necessary changes and start another round. One cycle may take weeks or even months.

Some of the prototyping can often be replaced with simulation.

”Let’s plan, create a simulation model and make a computer do calculations for a day or two. Then let’s then analyse the results and make necessary corrections. This will save us huge amounts of time and unnecessary prototype rounds”, praises Luukkainen.

According to Luukkainen, simulation suits nicely for example for antenna design, for analysing EMC, RF interoperability, shielding effectiveness and radiating fields. It can also be used to review the current layout, design and mechanics.

“Also the traditional prototypes are still of course needed”, he admits.

”Avoid unnecessary pondering and many prototyping rounds. Turn to an EMC and simulation specialist as early as possible”, advises Luukkainen.

SimulationWorkFlow.png

Proven in practice: simulation works

”I used to doubt the possibilities of simulation. A recent project made me however change my opinion”, tells Project Manager Niko Auvinen from Etteplan’s Espoo office.

”We designed the electronics to a device operating in a demanding industrial environment. The electronics included proper EMI (Electromagnetic Interference) filtering which was carefully designed according to best practices. Yet measurements revealed problems. A mobile phone brought close caused functional errors in the device”, tells Auvinen.

There was not much time. Auvinen contacted Etteplan’s Jyväskylä office and Senior EMC Specialist Marko Luukkainen there. He inspected the device, modelled it and made the simulator do the calculations. The results calculated by the simulator correlated quite accurately with the measurements obtained with a real prototype.

Picture - The correlation between measurement and simulation. Simulation estimates the levels and frequencies of RF radiation emitted by the device.

So, the simulation model was proven valid and accurate enough for the analysis of the design. The root cause of the EMC issues was soon revealed by analysing the simulation model and correlations between simulations and test results.

This convinced the design team of the benefits of EMC simulation. From this point on simulation was used to find the best possible layout design for the areas with the immunity problems.

With the qualified help of the Jyväskylä unit the problem source was identified and the device was adjusted accordingly.

”The EMC immunity problem was repaired quickly, and the customer received a product filling all the requirements in time”, rejoices Niko Auvinen.

”This project convinced me. Simulation is a very good tool to solve EMC problems” says Auvinen. He will definitely use simulation in the upcoming projects as well.

 

More information

Download a presentation about EM simulation:

EM_simulation.pdf

 

Marko Luukkainen
Senior EMC Specialist
Etteplan Jyväskylä

Niko Auvinen
Project manager
Etteplan Espoo

 

Related content

Analytics is a Process

Most industrial plants are already highly automated. Programmable controllers, sensors, computers have been common for decades and robots assemble products. But operative leaders naturally need to look ahead. We have automated our processes but what will the next step be? How to make our production line even more efficient? Could the data we collect be the answer?

Neste

Eatech (Part of Etteplan Group) implemented a mobile app for Neste that includes mobile refuelling, as well as a wide range of opportunities for customer marketing. Potential users of the application, which was released for iPhone and Android, are all the Finns traveling by car.

Posti

Eatech (Part of Etteplan Group) is Posti’s collaboration partner in charge of the maintenance of Posti’s parcel lockers. Eatech also participates in the development of the parcel locker system. The Continuous Services unit of Eatech carried out the modernisation of Posti’s parcel locker equipment and the implementation of the new software during autumn 2017. The work covered all parcel lockers in Finland.

Security - You’re blindfolded unless you scan for vulnerabilities

“This is a report from a customer project. Here we found several vulnerabilities when scanning a Linux-based device designed for industrial environments.”

Harri Susi, SW Testing & Cyber Security Specialist at Etteplan, is showing us a document that contains a detailed analysis of services provided by an IoT device and how hackers may be able to exploit it. A report like this is the first step towards more secure devices.

Contact us
Kalle Mannonen
Kalle Mannonen
Business Unit Director